常州电磁式无源贴片蜂鸣器 SMD-090025H侧发音 福鼎厂家直销3V
描 述
A. SCOPE
This specification applies magnetic buzzer, SMD-090025H-03027
B. SPECIFICATION
No.
Item
Unit
Specification
Condition
1
Oscillation Frequency
Hz
2700
Vo-p=1/2duty , square wave
2
Operating Voltage
Vo-p
2 ~ 4
3
Rated Voltage
Vo-p
3
4
Current Consumption
mA
MAX. 100
at Rated Voltage
5
Sound Pressure Level
dB
MIN. 80
at 10cm at Rated Voltage
6
Coil Resistance
Ω
16±3
7
Operating Temperature
℃
-30 ~ +70
8
Storage Temperature
℃
-40 ~ +85
9
Dimension
mm
Φ9.0x H2.5
See appearance drawing
10
Weight (MAX)
gram
0.8
11
Housing Material
LCP( Black )
12
Leading Pin
Tin Plated Brass(Sn)
See appearance drawing
13
Environmental
Protection Regulation
RoHS
C. APPEARANCE DRAWING
Tol : ± 0.5 Unit: mm
D.TESTING METHOD
Standard Measurement conditions
Temperature:25±2℃ Humidity:45-65%
Acoustic Characteristics:
The oscillation frequency, current consumption and sound pressure are measured by the measuring instruments shown below
In the measuring test, buzzer is placed as follows:
E. Typical Frequency Response Curve
F. Recommend Driving Circuit
The base current Ib should high enough so that it saturates the collector current of the transistor with the CB load.
G. Soldering Condition
(1)Recommendable reflow soldering condition is as follows
(Reflow soldering is twice)
Note:It is requested that reflow soldering should be executed after heat of product goes down to normal.
Heat resistant line
(Used when heat resistant reliability test is performed)
(2)Manual soldering
Manual soldering temperature 350 ℃ within 5 sec.
H. RELIABILITY TEST
NO.
ITEM
TEST CONDITION AND REQUIREMENT
1
High Temperature
Test (Storage)
After being placed in a chamber with 852℃ for 96 hours and then being placed in normal condition for 2 hours.
Allowable variation of SPL after test: 10dB.
2
Low Temperature
Test (Storage)
After being Placed in a chamber with -402℃ for 96 hours and then being placed in normal condition for 2 hours.
Allowable variation of SPL after test: 10dB.
3
Humidity Test
After being Placed in a chamber with 90-95% R.H. at 402℃ for 96 hours and then being placed in normal condition for 2 hours.
Allowable variation of SPL after test: 10dB.
4
Temperature Cycle
Test
The part shall be subjected to 5 cycles. One cycle shall be consist of:
Allowable variation of SPL after test: 10dB.
5
Drop Test
Drop on a hard wood board of 4cm thick, any directions ,6 times, at the height of 75cm .
Allowable variation of SPL after test: 10dB.
6
Vibration Test
After being applied vibration of amplitude of 1.5mm with 10 to 55 Hz band of vibration frequency to each of 3 perpendicular directions for 2 hours .
Allowable variation of SPL after test: 10dB.
7
Solderability
Test
Lead terminals are immersed in rosin for 5 seconds and then immersed in solder bath of +3005℃ for 31 seconds .
90% min. lead terminals shall be wet with solder
(Except the edge of terminals).
8
Terminal Strength
Pulling Test
The force of 9.8N(1.0kg) is applied to each terminal in axial direction for 10 seconds.
No visible damage and cutting off.
TEST CONDITION.
Standard Test Condition : a) Temperature : +5 ~ +35℃ b) Humidity : 45-85% c) Pressure : 860-1060mbar
Judgment Test Condition : a) Temperature : +25 ± 2℃ b) Humidity : 60-70% c) Pressure : 860-1060mbar
I. PACKING STANDARD
